{"id":14857,"date":"2015-01-22T08:00:18","date_gmt":"2015-01-22T13:00:18","guid":{"rendered":"https:\/\/www.detailedimage.com\/Ask-a-Pro\/?p=14857"},"modified":"2017-05-23T12:54:30","modified_gmt":"2017-05-23T16:54:30","slug":"carpro-hydro2-application-tips","status":"publish","type":"post","link":"https:\/\/www.detailedimage.com\/Ask-a-Pro\/carpro-hydro2-application-tips\/","title":{"rendered":"CarPro HydrO2: Application Tips"},"content":{"rendered":"

CarPro HydrO2<\/a> is a revolutionary sealant that allows you to protect paint, glass, metal, plastic, and nearly any other surfaces without wiping, buffing, or rubbing. \u00a0This touchless sealant is a breeze to use when done correctly, however there are many scenarios that may<\/em> lead to issues such as streaking. \u00a0In this article I will discuss some of the more common user mistakes made when using CarPro HydrO2 so that you will be better prepared to use this product properly and have a more enjoyable experience.<\/p>\n

Working in Sunlight or on Hot Surfaces<\/h2>\n

HydrO2 is not designed to be used in direct sunlight, or on any surface that is hot. \u00a0Your work area needs to be in complete shade, and the panels of your vehicle should be cool to the touch before using HydrO2. \u00a0This will ensure the product is not drying on the surface before you can rinse it, thus eliminating the risk of streaking in this situation.<\/p>\n

Using Too Much Product<\/h2>\n

One of the best features of HydrO2 is that very little solution (water + product mixture) is required to cover an entire vehicle. \u00a0On average, only 160mL (or ~5.4oz) of solution is required to cover a 4 door car. \u00a0There is no benefit to over applying, applying thick, or overlapping areas. \u00a0A light mist will yield the same amount of protection, and will reduce the chances of streaking as the product will be easier to rinse from the surface. \u00a0It seems to be a common issue of using way too much product per panel when applying HydrO2. \u00a0Simply set your spray trigger to a very fine mist<\/span> setting, and lightly cover the panel you are working on, then immediately rinse. \u00a0Easy as that!<\/p>\n

Allowing Product to Sit for Too Long<\/h2>\n

HydrO2 is meant to be applied and then immediately rinsed away<\/strong> using a strong stream of water. \u00a0In ideal conditions<\/em>, the product should be rinsed from the surface no more than 1 minute after you have started applying the solution to the panel you are working on. \u00a0Ideal conditions consist of low humidity, moderate temperatures, and a cool surface. \u00a0Since many of us will be using this product in warmer environments with potentially high humidity, it is important to remember to rinse the solution from the surface right away. \u00a0I recommend working on only one panel at a time, beginning with the horizontal panels (roof, then hood, then trunk) and then working your way around the vertical panels. \u00a0Mist a small amount of product onto the panel, and immediately rinse away (usually within 30 seconds from the time you started applying). There is no reason to let the product dwell on the surface. \u00a0Also, remember to thoroughly soak\u00a0the panel before application.<\/p>\n

Incorrect Dilution of Product with Water<\/h2>\n

HydrO2 is sold in a concentrated form. \u00a0The product needs to be diluted with distilled water to create the solution that will be used to spray on your vehicle. \u00a0The dilution ratio for HydrO2 is 4 parts of distilled water to 1 part of HydrO2 Concentrate. \u00a0This is very important, as a weaker dilution may yield decreased durability and gloss, while a higher dilution may make the product more difficult to use. \u00a0It is recommended that you only mix enough solution to use within a short period of time, so do not mix the entire bottle of concentrate if you do not intend on using it right away. \u00a0Simply mix a small amount before each job, and store the remaining concentrate indoors to help prolong the shelf life.<\/p>\n

Dilution Amounts for Common Spray Bottle Sizes (4 Water : 1 HydrO2)<\/strong><\/p>\n