JavaScript is turned off in your web browser. To shop with Detailed Image, please turn it on and then refresh the page.

Cookies are disabled in your web browser. To shop with Detailed Image, please turn cookies on and then refresh the page.

Bilt Hamber Filter Right

Bilt Hamber Touch-Less - 5 L

Add to Cart

$44.99

Available Sizes

1000 ml
$15.99
($0.02 / ml)

5 L
$44.99
($0.01 / ml)

Product Information

Unique pre-wash cleaner for thorough decontamination
Breaks down stubborn dirt, grime, and contamination
Can be diluted to various strengths
Product Codes: 1ltr-touch-less-1, 5ltr-touch-less-1
Read full description

Product Description

Bilt Hamber Touch-Less is an eco-friendly pre-clean, that delivers exceptional cleaning without contact. Unlike traditional cleaners with petrochemicals, Touch-Less is a biodegradable, sugar-based product that offers powerful cleaning of automotive paintwork. It effectively breaks down and lifts stubborn traffic film, road grime, and environmental contaminants, drastically reducing the need for physical agitation during the wash process, thereby minimizing the risk of scratches and swirl marks.

Applied easily via a pressure washer, pump spray, or trigger, Touch-Less also boasts easy rinsing properties, making subsequent bucket washes easier and allowing post-treatment products like waxes or sealants to bond more effectively. Touch-Less also contains powerful corrosion inhibitors and is safe for all vehicle finishes, including modern clear coats, wraps, and ceramic coatings.

If you are looking for a great pre-wash cleaner, add the Bilt Hamber Touch-Less to your detailing collection!

Application Tips:

Touch-Less uses the PIR dilution method and can be diluted to .5%, 1% or 2%.

1. Most foam cannons on the market have a 1000 ml capacity. Ensure your foam cannon is fully open, allowing for maximum foam. With the pressure washer hooked up and turned on, spray the foam cannon into a bucket until the foam cannon is empty. Once empty, measure the amount of water in your bucket.
2. If your foam cannon sprayed three gallons into the bucket, three gallons is equal to 11,356 ml.
3. Take 11,356 (volume in bucket) and multiply it by 0.02 (2% PIR). This will give you 227.12 ml.
4. Put 227 ml (round as needed) into your 1L foam cannon, and then top off with water to the 1L mark.
5. If you want to use 1% PIR multiply by 0.01, if you want to use 0.5% PIR multiply by 0.005.

From The Label

Product Description

Bilt-Hamber TOUCH-LESS is a renewable sugar-based biodegradable snow foam pre-wash that delivers excellent cleaning and free rinsing properties. Ideal before use of TOUCH-ON coating/shampoo. TOUCH-LESS cleans without the use of petrochemical surfactants, solvents, phosphates, caustics, NTA, preservatives or biocides. Includes powerful corrosion inhibitors.

Directions

SHAKE WELL BEFORE USE.

TOUCH-LESS may be applied with trigger spray, pump spray, pressure washer or snow foam lance. The minimum recommended dilution rate should be 0.5% PIR (Panel Impact Ratio) and up to 2% for very dirty vehicles. Where application is through trigger spray or pump spray, the dilution calculation is easy to achieve, however, for application with pressure equipment it is essential to determine the amount of water being delivered to the equipment reservoir. Use the following methods to calculate PIR:

Fill the detergent reservoir (on machine or lance) (A) up to capacity with plain water. Turn detergent feed to full. Take a large bucket or container (B) and discharge the lance into this, watching the reservoir until empty. Once empty stop.
The following calculations will achieve 2% dilution; Measure the total amount collected in (B) and multiply this number by 0.02 (Total can be measured in either volume with a measuring jug or by weight) this is the amount of TOUCH-LESS to use.
Add the calculated amount from Step 2 to the pressure-washer reservoir and top up to full with cold water and shake in for a few moments.

Alternatively, TOUCH-LESS can be applied using any pump, airless or trigger spray equipment - generation of foam is not important. Always allow the product to remain on the surface for a few minutes before rinsing - the longer the dwell time the better, but avoid allowing to dry.

Apply TOUCH-LESS to entire vehicle or panel by panel. Allow to soak for 1-5 minutes (but never allow to dry). Power-wash off.

Note:

It is not necessary to use all diluted TOUCH-LESS in one wash. One liter of diluted product can last 4-5 washes.
Apply to cool panels in shaded conditions.
Do not allow this product to dry in use.
Keep the bottle neck and lid clean.
Removed dirt, grime, salts and road film will deposit on drives and surfaces - ensure area can be cleaned