DI Accessories MTM Hydro 1.1 MM Orifice for Low Pressure Washers Reviews

This fit perfect in my harbor freight foam cannon and it also Increased the amount of foam.

the tip that came stock with my chemical guys foam cannon works better than the one I bought.. I have a electric pressure washer 1600 1.2 gmp

It really did change the amount of the foam.
I use this with Ryobi 1900psi electric pressure washer. This is awesome!

I noticed a big difference on the foam specially when you use a electric pressure washer

I love the nice thick shaving cream foam that this thing provides you definitely well worth the investment!!!

Good quality and holds soap well.

Item fits and works.

This is pretty decent I love how more foam come out of the foam cannon. What I love the most was the shipping time was fast.

Before my foam wasn't thick or staying on the car. Now after this little mod it's like snow stays on the car and super thick. Great fix.

This was a very good and very inexpensive option and oh my God the mounds of foam this helps my foam cannon produce on my electric pressure washer. This truly works amazingly! Best investment for any foam cannon!

This works awesome with my electric pw. Makes using a pw as good as gas powered pw.

ALL OF THE FOAM. Huge difference with every soap I have used with it. Carbon Collective Ultimus, CG Honeydew Snow Foam, Purple Power Vehicle and Boat Wash.

I have three different foam cannons, tried this orifice on all three with the same result. When installed, the foam cannon stops pulling the soap mixture in from the bottle. I'm not sure what the issue is, but it's disappointing.

Did not work on low or high pressure washer.

The products matter! I've 1st gotten a 1.1 orifice from amazon (forgive me DI) then 1 from DI. an Amazon foam cannon and MTM foam cannon. Here are the results: the orifice from amazon gave a a watery effect in both Amazon and MTM cannon. But DI orifice in the amazon did a better job, but in the MTM cannon it was like BAM (big time shaving cream)! I have a sun joe 3000 pw the only mod I did to replace the lance with a (1/4 inch) quick connect for the cannon. Don't forget to use good foam soap like: CG Honeydew and add HOT water (before the cold),so the soap be fully dissolve (Just like how I learn to make Kool Aid as a kid).

Works great, makes the foam stay on the car longer and its really easy to install.

I'd buy it again. I was definitely about to tell the difference between the old one and this 1.1mm.

The 1.1 orifice in a definite must have for low pressure washers. It made it look like a snow storm just hit and I used less product. I highly recommend it and you won't be disappointed with the results. Have fun with your new foam improved cannon!

After watching numerous YouTube videos on this mod, I was super excited to order this, but was I disappointed. I bought the fasmov foam Cannon from Amazon which gave me pretty decent foam, but after the install of the 1.1 orifice, it just didn't work or foam as as well. I even imcreased the amount of chemical guys Honey dew to compensate. This product was highly disappointing and didn't live up to the hype. I have a 1600 psi pressure washer btw.

Made a huge difference in the amount of foam i produced as well as how thick it is. This is a must buy for anyone with a low PSI/GPM pressure washer.

BUY IT! Unreal how it makes a huge difference. When you mix with proper soap to water ratio along with using HOT water it literally is like shaving cream. I'm using a "1800 psi" 2.0 GPM electric pressure washer and the results are insane. ENJOY!

A must have upgrade, improved the quality of my foam from thin and runny to thick and firm.

Works good for me

The 1.1mm orifice didn't work for me. It seems to let to much water through. My current foam cannon orifice has a smaller shaft and a rubber O-ring to seal it up. I've tried numerous settings and I do have a lower pressure washer. I'll keep it just in case I get a new one or a better power washer down the road.

The 1.1mm orifice transforms foam cannons being used with lower powered electric pressure washers. I'm using this with a 1.2 gpm Ryobi and cannot believe the improvement. This thing is the solution to weak foam from an electric pressure washer.

I would definitely suggest buying this to create more thick foam. I have a chemical guys foam cannon with a sunjoe electric pressure washer. I swapped out the offices and it creates a lot more foam.

Great product

Not sure, I really don't notice the difference. Might be because I'm not using the right soap, not sure to honest, or it might be because the one i was using already had the 1.1 orifice in it. Either way, not sure I don't know, but I still don't know what's the difference.

I'm using an AR 390SS, 2000 psi 1.4 GPM pressure washer. It was simple to change out the stock 1.25mm orafice in my Italian foam cannon for the 1.1mm replacement orifice from DI. The foam is much thicker, clingy and I use less product to boot. It helped me get better performance results while I was at already at the upper end of electric cleaning power and did not want the inconvenience of a gas pressure washer.

Moved to an electric pressure washer (1600 psi) from larger gas one (2600psi) and this is a must have if you want to produce decent foam at a lower operating pressure. Using an MTM foam cannon. Foam is still not as thick as the 2600psi pressure washer (with original orifice) as one would expect, however it is still thick enough that it stays on the car for long enough to do its job.

Just get one. It's cheap and it works. Doesn't matter what pressure washer you use. Tried on my sun joe and tried it on my Kranzle. It made the foam significantly better on both. Using it with a few ounces of your favorite foaming soap and you'll get shaving cream. Done and done.

Great item to use for a electric pressure washer produces thick foam and stays on the car longer!

This orifice made my cheap Amazon Goan cannon produce thick foam like you see on YouTube. My 1800psi electric pressure washer gives me professional results now. If you have an electic pressure washer, change your orifice to this one for thick foam. Best thing to happen to my foam cannon!

An absolute must have for anyone using an electric pressure washer 2000psi or less. The amount of foam created is a major difference and you also use less product because it works so much better. I highly recommend it.

This has almost doubled the amount of foam for my setup (karcher 1.3gpm/1800psi with PF22). I normally use Adams shampoo but tried CG Honeydew and the foam stayed on the car for over 10 mins, was not runny at all. So anyone with a low gpm washer, this is a must. Just know that a lot of the amazon sprayers already come with 1.1 orifice. So check/confirm before you buy it.