P&S Triple S Installation Wrap Solution - 16 oz
$23.99
Available Sizes
16 oz
$23.99
($1.50 / oz)
128 oz
$63.99
($0.50 / oz)
Product Information
- Makes applying vinyl wraps and ppf incredibly easy!
- Easy spray on formula
- Fresh watermelon lemonade scent
- Contains UV protection
- Product Codes: C8016, C8001
- Read full description
Product Description
The P&S Triple S Installation Wrap Solution is an all-in-one solution for easy vinyl and ppf applications! Triple S stands for three important "S" in the vinyl wrap installation process, Slip, Slide, and Shine. It was custom designed by P&S Detail Products for The Rag Company to meet and exceed specific requirements of The Wrap Institute (TWI). During the prep phase of an install, Triple S can be applied to high points, curves and large flat areas. It can also be used to eliminate sanding and adhesive lines while allowing films to slide easily across the surface (Slip). During the wrapping process, installers can spray Triple S on the squeegee buffer. This dramatically reduces scratches which ensures quality. It also helps the squeegee glide faster across the surface which lowers install times and reduces fatigue (Slide). Once the wrap is done, Triple S can be applied over any wrap: commercial, color change and PPF. It enhances all gloss finishes and helps keep sensitive matte finishes perfectly preserved (Shine). Triple S smells amazing (watermelon lemonade scent) and enhanced UV protection helps maintain your wrap's finish. Make applying your vinyl wraps easier with the all-in-one P&S Triple S Installation Wrap Solution.From The Label
Product Description
SLIP - SLIDE - SHINE
Triple S is the ultimate all-in-one solution for prep, install and post install workflow when wrapping vehicles with commercial, color change and PPF. Triple S helps ensure the highest quality and workflow for installers wile providing a superior finish that customers can see and feel, all in one bottle! For prep (SLIP), wiping the surface down with Triple S eliminates sanding and adhesive lines while allowing even the most difficult films to slide easily across the surface. During the install (SLIDE), spraying Triple S on the squeegee buffer enables it to slide effortlessly and scratch-free across the wrap film. For post install (SHINE), wiping the wrap down with Triple S enhances the wrap while leaving a protective finish that lasts and lasts.
Triple S is the ultimate all-in-one solution for prep, install and post install workflow when wrapping vehicles with commercial, color change and PPF. Triple S helps ensure the highest quality and workflow for installers wile providing a superior finish that customers can see and feel, all in one bottle! For prep (SLIP), wiping the surface down with Triple S eliminates sanding and adhesive lines while allowing even the most difficult films to slide easily across the surface. During the install (SLIDE), spraying Triple S on the squeegee buffer enables it to slide effortlessly and scratch-free across the wrap film. For post install (SHINE), wiping the wrap down with Triple S enhances the wrap while leaving a protective finish that lasts and lasts.
Directions
Prep - Slip:
Clean, clay bar and degrease the vehicle. Generously spray Triple S on the section to be installed and polish it evenly across the surface with a high quality microfiber towel. Wipe Triple S off the outside edges and any recessed areas with 70% IPA (roughly 1" wide). This will help ensure maximum adhesion on these key durability areas. Allow Triple S to dry completely (10 - 15 seconds) then move to Install.
Install - Slide:
Spray the squeegee buffer thoroughly on both sides with Triple S (prep squeegee in a safe area to avoid slipping or over spray). Squeegee wrapping film in a standard manner. Reapply Triple S to the buffer as needed during the install. Once the panel is applied, move to the Post Install protocol.
Post Install - Shine:
Spray the wrapped section with Triple S as soon as the install is completed. For best results, use a high quality polishing microfiber towel. Spread and buff Triple S evenly across the surface to ensure full coverage and protection.
Clean, clay bar and degrease the vehicle. Generously spray Triple S on the section to be installed and polish it evenly across the surface with a high quality microfiber towel. Wipe Triple S off the outside edges and any recessed areas with 70% IPA (roughly 1" wide). This will help ensure maximum adhesion on these key durability areas. Allow Triple S to dry completely (10 - 15 seconds) then move to Install.
Install - Slide:
Spray the squeegee buffer thoroughly on both sides with Triple S (prep squeegee in a safe area to avoid slipping or over spray). Squeegee wrapping film in a standard manner. Reapply Triple S to the buffer as needed during the install. Once the panel is applied, move to the Post Install protocol.
Post Install - Shine:
Spray the wrapped section with Triple S as soon as the install is completed. For best results, use a high quality polishing microfiber towel. Spread and buff Triple S evenly across the surface to ensure full coverage and protection.
Customer Reviews
Sorry, there are no reviews yet. Be the first one to write a review!
Customers Who Bought This Item Also Bought
Related Items
Related Categories
